Top - 9 Best Drills

Using a drill can greatly facilitate the repair work. Today, a really huge assortment of these products is presented in construction tool stores, so it is easy for an inexperienced person to get confused in them. Keep in mind that the main function of a drill is to drill holes in a variety of materials - wood, metal, concrete, brick, cement mortar or plaster, and so on. Before you buy this equipment, you should find out what parameters should be chosen. With this, we, perhaps, will begin a review of the best products.

What criteria influence the choice of a drill?

For homework, do not buy a professional tool - its price is an order of magnitude higher than that of household structures, but it is unlikely that you can use all the functions of such a drill at home. It is much better to dwell on the average parameters of the device. One of the key points is the power consumption of the equipment - a tool with this parameter from 500 to 900 watts is quite suitable for the home. It is worth noting that the power of the equipment directly affects the mass of the device, therefore, the ease of use.

Another important point is the shaft idle speed - this information is also given in the product passport. The higher this parameter is, the smoother the walls of the drilled hole will be. High torque allows you to work with fairly hard materials even with a small power device. For grinding, such a parameter will be an indispensable assistant. It is desirable that there was still speed adjustment - in this case, the drill can be used as an ordinary screwdriver.

The diameter of the hole is also important - usually the manufacturer gives these maximum and minimum parameters for all basic materials, the diameter of the drill is also indicated. The cartridge must be paid attention to: it can be either quick-clamping or key. The latter variety needs the use of a special key, but it holds it much more reliable, therefore all powerful and impact products are equipped with this cartridge, although the key can be lost. Keyless chucks do not require the use of an additional tool, but they serve less than the key, and even are prone to breakage.

The largest drill diameter also plays a role - it is best to purchase drills with this parameter of 13 or 16 mm. A number of additional functions allows you to ensure ease of use of the product and increase safety. In particular, many drills are equipped with a soft start mechanism, due to which revolutions will be gained gradually, jerks will not occur during start-up, which ensures an exact hit in the drilled hole.

When developing our review, we took into account not only all these points, but also the feedback from users and professional repairmen, as well as the price-quality ratio of the device. We hope that the information we provide will be very useful for you and help you quickly decide on the most suitable model.

The best classic drills

3. Bosch GBM 13 HRE (VIZ)

This model has excellent performance, in addition, its price is not too high. This drill is perfect for precision drilling jobs. The torque is 60 Nm, when working with steel, the maximum diameter of the holes is 13 mm, with aluminum this parameter increases to 20 mm, a hole can be made in wood up to 20 mm. It is possible to adjust the number of revolutions, so the drill can also be used to tighten screws or self-tapping screws. The case is made of durable rubberized plastic, it is convenient to hold it in your hands: it does not slip out. An extra handle is included, making the device even more convenient. Management is quite simple - to start the engine just click on the appropriate button. On it is the lever, which is responsible for adjusting the number of revolutions.

There is a reverse rotation, so if the drill gets stuck, it can be easily removed from any material. The design has milled gears, a robust gear housing and needle bearings, which increases the life of the product. The highest power consumption is 550 watts with an output power of 285 watts. At idle, the largest number of revolutions is 550 per minute, with a load not exceeding 380 revolutions.

Benefits:

• High reliability;
• Superior build quality
• Torque is good for home use;
• Acceptable price.

Disadvantages:

• A short supply cable, you have to immediately stock up on carrying;
• Not provided shock mode;
• Unreliable speed adjustment wheel.

2. Makita DP4001

It has one of the most reliable gearboxes among all the models presented in our review. It provides a torque of up to 51 Nm, which makes it possible to easily cope even with rather complex jobs that need serious pulling force. The device has everything you need for a long and comfortable operation. The design provides for a system for adjusting the number of revolutions, an effective reverse. The drill is equipped with a quick-clamping chuck with a single coupling, so that it will be possible to change drills and nozzles very quickly.

At idle, the device is capable of delivering up to 900 rpm with a power consumption of 750 watts. The mass of the product is only 2.1 kg, it has an extra handle made of rubberized materials. The largest diameter of the drill is 13 mm, which is quite enough for domestic work. In a metal with the help of such a drill, a hole with a diameter of up to 13 mm can be made, in wood - up to 38 mm.

Benefits:

• The presence of a keyless chuck;
• Small design;
• If desired, the cartridge can easily be replaced by a key;
• The additional handle rubberized.

Disadvantages:

• After some time, the brushes begin to sparkle strongly;
• Also, over time, a not-so-pleasant sound arises when gaining speed.

1. DeWalt DWD522KS

This is one of the most convenient to use shock-free models, the development of which was perfectly balanced mass, so even with prolonged use, the hands will not get tired. In addition, this design solution significantly reduces vibration, which is especially important when working with solid materials such as steel or concrete. The power of the product is 550 watts - it is quite suitable for home conditions. Thanks to this parameter, a hole with a diameter of up to 10 mm can be drilled in the metal. The number of revolutions will pleasantly please you - 2800 per minute idling, which greatly increases the performance of this tool.

Users praise this model for a long cord and a powerful keyless chuck, the maximum diameter of the drill does not exceed 10 mm. Adjustment of the electronic type speed, due to which you can choose the ideal torque for each material. In addition, such a drill is equipped with a torsion button lock.Users notice that there is no additional handle in the kit, which is why holding it is not very convenient.

Benefits:

• Very convenient and reliable cartridge;
• Convenient adjustment of the number of revolutions.

Disadvantages:

• High price.

The best percussion drills of the budget segment

3. Bort BSM-650U

It works from an ordinary electric network, copes well with materials such as wood, metal and concrete. The model has a reverse mode and a function for adjusting the number of revolutions, which allows you to use the drill as a screwdriver. For even greater ease of use, the additional handle has a special compartment for storing drills - this allows you to constantly keep them handy during operation. The power of the product is 650 watts, a bright LED is located under the cartridge, which will highlight the drilled area.

The weight of the drill is 2 kg, it is equipped with a keyless chuck, where you can install a drill with a diameter of up to 13 mm. Using this product, you can drill a hole in the metal, the diameter of which will be up to 10 mm, in wood - up to 25 mm. The model is equipped with an additional handle with an insert made of dense rough rubber, which will fit snugly into the hand, the function of hammer drilling is provided. This makes it easier to work with concrete and cement.

Benefits:

• Perfect value for money;
• Good product reliability;
• High power;
• The presence of shock mode;
• Long warranty - 2 years.

Disadvantages:

• The motor becomes very hot during continuous operation.

2. Bison DU-810 ERM2

This is a fairly inexpensive model, which is ideal for home use. The product is placed in a plastic rubberized case, which not only fits comfortably in your hand, but is also not subject to any kind of damage. The kit comes with an additional handle that facilitates the use of a drill. All controls are located in close proximity to each other, so all operating modes are switched literally with one finger. There is a wheel on the engine start button that controls the number of revolutions, a lever is provided above it that responds to the choice of the operating mode - normal or reverse. On the left side of the main handle there is a button that allows for continuous operation.

Among the inexpensive models, this is one of the most powerful drills - this figure is 810 watts, the number of revolutions at idle is 2800 per minute. The cartridge is installed key, which is very important to ensure safety with similar torque. The number of beats per minute reaches 42,000. This feature greatly facilitates the work with the hardest materials. Users also note a fairly long warranty on this device - as much as 5 years.

Benefits:

• Very comfortable design;
• Lightweight and compact in size, due to which it is suitable for use in hard-to-reach places;
• Good for home;
• Sufficiently long supply wire;
• Great value for money.

Disadvantages:

• Sometimes models with strong backlash of a cartridge come across, therefore it should be replaced right after this defect is revealed.

1. Interskol DU-580ER

This is the best percussion drill in a fairly cheap price segment. It is characterized by excellent workmanship, has advanced functionality, and therefore is deservedly popular. The power of the product is 580 W, thanks to this indicator, you can drill holes in concrete with a diameter of up to 12 mm. When idling, the device produces up to 2800 rpm, which allows for a high level of performance. The mass of the device is only 1.4 kg - it can easily be held even with one hand.

Handles are ergonomic, do not slip out of palms. The design is made of high-quality materials, due to which, therefore, it differs by a long period of operation, and all functions will work in normal mode.Hammer drilling facilitates work with solid materials, reverse rotation is provided. An additional handle is included, the cable is elongated, so you can use it without an extension cord. There is a special limiter for receiving holes of a given length. The only negative point that users note is that the engine heats up very much during operation.

Benefits:

• High power for home use;
• Good quality production;
• Adjustment of working power;
• Acceptable power;
• Long power cable.

Disadvantages:

• In addition to the warming motor during long work, it was not found.

The best percussion drills in terms of value for money

3. DeWalt DWD024

This model is characterized by small overall dimensions, which allows you to hold it even with one hand. Just in case, the manufacturer supplied this drill with an additional rubberized handle. It will come in handy if you have to work with materials that require additional efforts when drilling. The cartridge is the key, as in most impact drills. It allows you to reliably clamp the drill or drill, prevents it from slipping out, which often happens with quick-clamping chucks. There is a special mechanism that provides precise adjustment of the drilling depth.

For continuous operation, there is a special button that blocks engine shutdown. The design has a reverse function, so the drill can also be used as a screwdriver. The adjustment of the number of revolutions and speed is smooth, without jerking. It has a power of 650 watts with a mass of less than 2 kg. Users note a fairly long power cord - 2.5 meters, thanks to which you can use this device without an extension cord.

Benefits:

• Excellent build quality, there are no backlashes and extraneous creaks;
• Reliable cartridge;
• Long service life;
• High power.

Disadvantages:

• Not suitable for mixing mortars.

2. Makita HP1620

This is a universal drill that can drill not only hard materials, but also softer ones - plastic, drywall and so on. The speed of rotation is regulated quite smoothly, which allows you to choose the required number of revolutions for a particular material. The maximum idle amount is 2800 per minute. If the device is used in shock mode, then per minute there will be up to 44,800 strokes. There is a reverse, carbon brushes, due to which the power will be preserved during both the main and reverse modes. The case is made of reliable plastic that can withstand severe physical stress - shock, fall, and so on. The mass of the device is small, so it can easily be held in hands for quite a long time.

Power consumption of the drill is 650 watts, output - 380 watts. The device operates on the basis of a universal commutator motor, the maximum diameter of the drill being installed is 13 mm. The key holder, on the power cable there is a special clip for storing the key. Many users note that a drill can work with a number of materials such as glass, hardened steel, plywood, granite, marble and so on.

Benefits:

• Works perfectly in both shock and normal mode;
• Light weight;
• Beautiful appearance, the case is made of shockproof plastic.

Disadvantages:

• No case included.

1. Bosch PSB 750 RCE Case (BZP)

This is the best percussion drill in terms of price and quality, as well as according to user reviews. The device is characterized by excellent reliability, truly German, although the cost is quite high compared to other models, such a drill is still very popular. This design is equipped with a convenient keyless chuck, which is not quite typical for an impact drill. It is reliable enough, so drills or drills will not slip out during operation, and besides, it can be used to quickly replace the drill. The power of the product is 750 W - one of the highest among all the models included in our review.The highest torque is 10 Nm, so the device will quickly pass even through fairly hard materials.

The kit includes a decent-sized case, which will include not only the drill itself, but also various additional nozzles, crowns, drills and so on. A depth limiter is provided; it is made of a rigid metal rod. It is possible to fix the spindle. The device is able to work for quite a long time without overheating. The brushes are installed carbon, resistant to abrasion, during operation do not start to sparkle.

Benefits:

• High-quality German assembly;
• All parameters declared by the manufacturer are true.

Disadvantages:

• With dusty work, the reverse can become clogged, otherwise the device does not have negative aspects.

In conclusion, an interesting video

In conclusion, we want to express the hope that all the information has been quite useful to you. If you have certain considerations regarding a particular model, or if you are going to share your experience with other users, then you have comments on this article at your disposal.

(2 ratings, average: 5,00 out of 5)

Loading...